Porta ethernet (Modulos ethernet only): 10Base-T half duplex RJ45 ConectOu
Link e Activity IndicadOues LED
Electrical Isolamento 1500 V RMS at 50 Hz to 60 Hz fOu 60 s, applied as
specified in section 5.3.2 De IEC 60950: 1991
Ethernet Broadcast StOum Resiliency = less than Ou equal to 5000 [ARP] frames-
per-second e less than Ou equal to 5 minutes duration
Shipped com Each Unit: Mini-DIN to DB-9M serial cables
4 ft RS-232 Configuração cable
2.5mm Parafusodriver
CD (docs e Configuração utility)
RS-422/485 DB-9 to Parafuso Terminal AdaptOu (1 Ou 4, depending on POutas)
Porta serial Isolamento: 2500 V RMS port Sinal Isolamento per UL 1577
3000 Vcc min. port to ground e port to logic potência Isolamento
Aplicação Portas: Modbus Plus Conector
Two DB9 Fêmea Padrão Modbus Plus Conectores
Configuração Porta serial: DB-9M RS-232 only
No hardware handshaking
Indicadores LED: potência e Módulo Status
Aplicação Status
Porta serial Activity
Porta serial Estado de erro
Dimensões: Padrão:
5.20 in H x 2.07 in W x 4.52 in D (13.2 cm x 5.25 cm x 11.48 cm)
Estendido:
5.20 in H x 2.73 in W x 4.52 in D
(13.2 cm x 6.934 cm x 11.48 cm)
Humidade relativa: 5% to 95% (sem condensação )
Temperatura de armazenamento: -40° F to 185° F (-40° C to 85° C)
Temperatura de operação: -4° F to 122° F (-20° C to 50° C)
Current Load: 500 mA max @ 32 Vcc max
Fonte de Alimentação: 24 Vcc nominal
18 to 32 Vcc allowed
Positive, Negative, GND Terminals
2.5 mm screwdriver blade
Condições ambientais: -20 to 50DEG C Operating, -40 to 85DEG C Armazenamento, 5 to 95 % Humidade
Peso: 5.2
Tamanho: 2.07
Comprimento: 4.52
Invólucro: Aluminum
Software Requirements: Drivers
Conectividade: Serial
Classificação de frequência: 50 to 60
Configuração: Yes
Data Transfer Rate: 110 to 115
Port: 4
Interface: RS-232, RS-422, RS-485
Ethernet: 10Base-T
Padrão: ATEX, CE/EMC, Environmental, UL,GOST-R
Aplicação: Manufacturing, Oil e Gas, Electrical potência e Food Processing.
Características especiais: Ideal solution for applications where DNP Conectividade can be used to integrate a PROFIBUS DP Slave device into a system. Powerful Módulo designed com Client support, enabling easy Conexão to Rockwell Automation PLCs (CLX, SLC, PLC, CPLX, e similar Dispositivos).
Tipo: Stand-alone Gateway
Sub-Categoria: 5000
Marca: PROSOFT
The ProLinx DNP 3.0 Slave to PROFIBUS DP Master Gateway creates a powerful connection between devices on a PROFIBUS network and DNP devices. This stand-alone DIN-rail mounted protocol gateway provides one serial port and one DB9F port configurable for PDPM. The DNP 3.0 Slave protocol driver supports Slave implementations of the protocol on one port. This port is fully configurable. The PROFIBUS DP Master protocol driver supports Master implementations of the protocol on either a Mono-Master or Multi-Master network.
